Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Do people really expect no filler on their cars?

  1. #11
    A properly metal finished car will still have SOME filler. But we’re talking extremely minimal amounts.

    “Sculpted” 911s should have died out in the 80s and 90s when slant noses, 959, and 993 body kits became pasé.
    -Marco
    SReg. #778 OGrp: #8 RGrp: #---
    TLG Auto: Website
    Searching for engine #907495 and gearbox 902/1 #229687

  2. #12
    Member
    Join Date
    Jul 2015
    Location
    CT and NY
    Posts
    57
    Yeah, that's a lot of filler. It takes time to fit panels and it looks like the outer rocker was welded in too low. Rocker is installed based on the door, maybe the door was off the car when installed, I don't know. Upper door filler is where the factory used lead, very difficult to get right in that spot where the fender and door curve together. These cars cars had complex curves and shapes where panels meet up, so they used lead in spots from the factory. This stuff just isn't easy.

    Honestly, yeah that is how a lot of bodywork is done these days, if you read autobody books or watch car shows, you'll see how some shops completely fill gaps and then cut through the filler to create a perfect gap, it's a well known trick. I have seen the technique used on one of Chip Foose's TV shows. Check out the video below. Link isn't from Chip Foose show, but demonstrates the trick. It's a technique in books, out there on youtube, on TV and in the real world. That is why I started this post, this is more or less standard, a lot of shops use this technique. Filler use is really a judgement call, standards are changing and there is more info out there now.


    https://www.youtube.com/watch?v=gms-PS2GcOE
    Last edited by David Liam; 10-19-2017 at 06:16 PM.
    Runge Eleven
    david@rungeeleven.com
    www.rungeeleven.com
    Porsche 911 Corrosion/Collision Repair Specialist

  3. #13
    Member
    Join Date
    Jul 2015
    Location
    CT and NY
    Posts
    57
    another gap video:
    https://www.youtube.com/watch?v=qTgevVs85qI

    In my opinion, the panels are "cupped" and when they meet, they aren't laser straight from side to side. But, the way these cars get blocked, they sort of lose their natural cupping. The door and quarter usually have their own crown to them sort of, it's tough to explain, I saw a great picture of it once with a guy holding a straight edge across a door gap, the actual gap was below the straight edge, it fell away from the slight cupping. It was an 80s 911 though, maybe there was more cupping in the panels then.

    Anyone else notice this?
    Runge Eleven
    david@rungeeleven.com
    www.rungeeleven.com
    Porsche 911 Corrosion/Collision Repair Specialist

  4. #14
    Filling the gaps, then cutting them out was how the 356's were done, mostly because the quality of stamped panels wasn't so good. Yet people rave about how wonderful the gaps were, yet it was all done with filler (lead in this case)
    As to the "falling off" of the door panels/ fender panels, isn't that why panels should be board sanded in place, not with doors laying on saw horses?
    Early S Registry member #90
    R Gruppe member #138
    Fort Worth Tx.

  5. #15
    Member
    Join Date
    Jul 2015
    Location
    CT and NY
    Posts
    57
    I prefer to block sand with all of the panels on the car, but I am careful to sand lightly around the edges to make sure there isn't a hard edge that doesn't look like something sheet metal would do. I was just being fussy and pointing something out that people might not ever think about. Overall, I notice original cars have a slightly different look than redone cars. It's important to be careful with all of this high build, spray-able polyester stuff, the cars can get puffy. It's subtle, but noticeable.

  6. #16
    Member
    Join Date
    Jul 2015
    Location
    CT and NY
    Posts
    57
    Below is an example of a faked gap where filler was stacked up in the corner of the hood to bring it up to the cowl. Funky and doesn't look like sheet metal. But, every project has a budget and there is no such thing as a perfect paint job, so I don't want to say that this is a complete sin, it's just what's out there on a lot of cars. People should be looking for this type of thing and be careful when choosing a body shop.

    Name:  early 2 hood.jpg
Views: 260
Size:  58.2 KB
    Runge Eleven
    david@rungeeleven.com
    www.rungeeleven.com
    Porsche 911 Corrosion/Collision Repair Specialist

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Message Board Disclaimer and Terms of Use
This is a public forum. Messages posted here can be viewed by the public. The Early 911S Registry is not responsible for messages posted in its online forums, and any message will express the views of the author and not the Early 911S Registry. Use of online forums shall constitute the agreement of the user not to post anything of religious or political content, false and defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, or otherwise to violate the law and the further agreement of the user to be solely responsible for and hold the Early 911S Registry harmless in the event of any claim based on their message. Any viewer who finds a message objectionable should contact us immediately by email. The Early 911S Registry has the ability to remove objectionable messages and we will make every effort to do so, within a reasonable time frame, if we determine that removal is necessary.