Page 1 of 2 12 LastLast
Results 1 to 10 of 11

Thread: Tach challenge

  1. #1

    Tach challenge

    Looking for some help. I have a 1970 911 that I installed a 3.0, now the tach doesn't work. The shop told me to install a SC tach. I don't want to install it wrong.

    The original tach went from left to right blue wire yellow stripe, black and purple and the brown was a ground. Do I hook it up the same way with the SC tach?

    Thanks
    Don
    Attached Images Attached Images

  2. #2
    Just look at the symbols on the spade connectors. Blue/yellow is power and goes to the + terminal (or it may be marked 12V) Black/purple goes to terminal TD, and brown is always ground and goes to terminal marked with a -
    Early S Registry member #90
    R Gruppe member #138
    Fort Worth Tx.

  3. #3
    Yes Ed power on blue yellow. Connected it that way turned key on tach went to 6 grand with out running.

  4. #4
    The problem is not the tach but, rather, the tach signal. The early ignition (3-pin CDI) is a TD signal. The later SC ignition (6-pin box) is a different tach signal.

    Have your original tach converted or use the SC tach.
    -Marco
    SReg. #778 OGrp: #8 RGrp: #---
    TLG Auto: Website ... Blog ... Facebook Page
    Searching for engine #907495 and gearbox 902/1 #229687

  5. #5
    Put in a SC tach because the original tach did not move

  6. #6
    But the problem is still the signal to the tach. Contact Bob Ashlock at Ashlock tech. He makes an adapter that should work for you.
    Early S Registry member #90
    R Gruppe member #138
    Fort Worth Tx.

  7. #7
    Thanks Ed, I called Bob nice guy, I need to check engine harness to CDI box to see if TD wire is connected. I ordered the adapter, rather use original tach anyway.

  8. #8
    Watch yourself on that blue/yellow wire. 350V DC on it!

  9. #9
    BLUE/YELLOW is battery voltage. I received tach adapt from Bob, installed today with original tach, it works fine. Tapped in at RPM ballister on relay panel. 14 pin from engine harness TD is on #12, harness to tach is on #8. Where should the pin be located on the engine harness side? SC tach is bad, the original tach is working fine. I would like to put the TD in the original 14 pin harness.

  10. #10
    Pin 8 of the 14 pin connector on an SC engine harness is unused on the female side.
    If the tach signal on the 14 pin male side for the 70 is pin 8, (I forget right now, it is late, but trust what you are saying) move the SC engine harness tach wire to pin 8.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Message Board Disclaimer
This is a public forum. Messages posted here can be viewed by the public. The Early 911S Registry is not responsible for messages posted in its online forums, and any message will express the views of the author and not the Early 911S Registry. Use of online forums shall constitute the agreement of the user not to post anything of religious or political content, false and defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, or otherwise to violate the law and the further agreement of the user to be solely responsible for and hold the Early 911S Registry harmless in the event of any claim based on their message. Any viewer who finds a message objectionable should contact us immediately by email. The Early 911S Registry has the ability to remove objectionable messages and we will make every effort to do so, within a reasonable time frame, if we determine that removal is necessary.