Results 1 to 4 of 4

Thread: Sound deadening 1973

  1. #1
    Senior Member NorthernThrux's Avatar
    Join Date
    Jun 2012
    Location
    London, Ontario, Canada
    Posts
    1,377

    Sound deadening 1973

    What's the current thinking of sound deadening for the floor pans for 72-73? I have the original insulation in the rear tub/parcel shelf etc. and no rust under it whatsoever. SO that's all good. On the floors I also have no rust but we chipped away some of the tar stuff with the hexagonal imprint at places where it had cracked to check for rust. All looked good, but now I have a few sections of bare metal where we did scraping (including almost all of the driver's side pan) and the remainder with the original black material. I've used POR15 over the bare metal but am wondering what I should do on top of that? Just leave it? Use rubberized coatings like Wurth etc? Or use some kind of modern audio or vibration damping material? What to people think?

    Ravi
    Early 911S Registry # 2395
    1973 Porsche 911S in ivory white 5sp MT
    2015 Porsche Macan S in agate grey 7sp PDK

  2. #2
    Senior Member
    Join Date
    Nov 2010
    Location
    Darien, CT
    Posts
    127
    These seem to be popular with full resto crowd. Was the way we are leaning with our 69 resto.

    http://www.repaintsupply.com/3m-0884...ads-p6102.html

    3M 08840

    Scott
    69 911S #1379
    65 356 SC #130757

  3. #3
    Senior Member csbush's Avatar
    Join Date
    Jan 2009
    Location
    San Antonio Texas
    Posts
    474
    That 3M pad is what I am using in my 73 restoration. I think it is important to help absorb road noise. It does lay down nicely, and fits the contours of the floor pan. It looks about as original as I have seen- unlike dynamat and other sound deadening. They also look very similar to the replacement pads from Porsche I was able to buy in the mid 80’s when I replaced the sound deadening on my 70 911.
    Chuck

    Early 911S registry #380
    '70S
    '75S
    '96 C4S
    '65 R69S

  4. #4
    Senior Member NorthernThrux's Avatar
    Join Date
    Jun 2012
    Location
    London, Ontario, Canada
    Posts
    1,377
    Thank you both. I hadn’t seen that product, but it turns out it is made in the 3M factory right here in town, so I can support a “local” business.

    Ravi

    EDIT: For future reference, NAPA carries this in the US and Canada.
    Last edited by NorthernThrux; 08-15-2019 at 06:17 PM.
    Early 911S Registry # 2395
    1973 Porsche 911S in ivory white 5sp MT
    2015 Porsche Macan S in agate grey 7sp PDK

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Message Board Disclaimer
This is a public forum. Messages posted here can be viewed by the public. The Early 911S Registry is not responsible for messages posted in its online forums, and any message will express the views of the author and not the Early 911S Registry. Use of online forums shall constitute the agreement of the user not to post anything of religious or political content, false and defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, or otherwise to violate the law and the further agreement of the user to be solely responsible for and hold the Early 911S Registry harmless in the event of any claim based on their message. Any viewer who finds a message objectionable should contact us immediately by email. The Early 911S Registry has the ability to remove objectionable messages and we will make every effort to do so, within a reasonable time frame, if we determine that removal is necessary.