Page 1 of 2 12 LastLast
Results 1 to 10 of 14

Thread: FS: Very early 4 screw dash top 1964 - 1965

  1. #1

    FS: Very early 4 screw dash top 1964 - 1965

    Hi,

    available is a very early 4 screw dash top. This is the correct dash top for cars made in 1964 and early 1965. As per B.Johnson "the newest car ... which has these is 301175".

    Overall condition is good. There is a small crack infront of the speaker. I assume this can be fixed easily as the vinyl is still there. Another crack on the lower angle, which can be hardly seen when installed. The original vinyl has some decoloration.
    $600 + shipping

    Mark
    Attached Images Attached Images

  2. #2

  3. #3
    You have a pm.Thanks.

  4. #4
    In his 911/912 authenticity book, Brett Johnson wrote concerning the 4-screw dash, "The newest car in my file which had these is 301175." He doesn't claim to have complete data, just none beyond 301175. I can add that 1965 Porsche 911 chassis number 301258 has it's original dash and it is the 4-screw variety. I am just guessing now but the 4-screw dash may have run through the end of the 1965 model year production somewhere around chassis number 302010.
    Indiana,
    1965 911: 300594, 300839
    1965 912: 350407,
    1968 911L SWT Sportomatic,
    1970 911T Irish Green, Restored,
    1974 911 Carrera, 1975 911 Carrera,
    1970 914 1.7 Signal Orange, 1973 914 2.0 Zambezi Green, 1974 914 2.0 Ravena Green--this one is for sale
    Used to haul the kids to the pool in 356/1500RS Carrera Speedster 80820. Wife would leave it in the shopping center parking lot -- now in the Porsche Factory Museum.

  5. #5
    Senior Member Varooom's Avatar
    Join Date
    Oct 2006
    Location
    SoCal
    Posts
    653
    Do you have a picture of the correct screws that hold that dash?


    .
    Steve Var.
    _____________
    61 356B
    67S
    66 912
    66 Fulvia
    72 914

  6. #6
    Senior Member moito's Avatar
    Join Date
    May 2013
    Location
    AUSTRIA (tu felix)
    Posts
    6,699
    Quote Originally Posted by Varooom View Post
    Do you have a picture of the correct screws that hold that dash?


    .
    pump for a pic

  7. #7
    Senior Member Robert-Jean's Avatar
    Join Date
    Feb 2008
    Location
    Netherlands
    Posts
    105
    Quote Originally Posted by Auto*Legends View Post
    In his 911/912 authenticity book, Brett Johnson wrote concerning the 4-screw dash, "The newest car in my file which had these is 301175." He doesn't claim to have complete data, just none beyond 301175. I can add that 1965 Porsche 911 chassis number 301258 has it's original dash and it is the 4-screw variety. I am just guessing now but the 4-screw dash may have run through the end of the 1965 model year production somewhere around chassis number 302010.
    No, this type of dashboard ended before VIN 302010.
    One of the last is VIN 3001379.
    Jacques (PSS) can shed some light on this.
    Question, is it a four or five button dashboard?

    20191225_232915.jpg

  8. #8

    Number of buttons

    I'll let Mark answer the number of screws on his dash

    (his photo shows the fifth over the glove box).

    The screws that hold the dash have a shaped head that holds the rubber cap. The screw example (below) is from a 1968 VW Type Two (the drivers seat partition, on a walk thru interior) Note the skirt on the VW item. The 1964-65 Porsche dash button has a rounded bottom edge rather than the skirt.

    We would hope our friends in Germany have a better source for Type 2 interior bits - I can't find any here in the USA.
    Attached Images Attached Images
    Bob
    Early S Reg #370

  9. #9
    Senior Member haul's Avatar
    Join Date
    Jul 2014
    Location
    bavaria
    Posts
    2,327
    ............if you do know L length and D diameter...should be easY
    Attached Images Attached Images
    59 750 pre unit triton
    63 650 gray silver bikinitub triumph thunderbird
    70 650 astralred silver triumph bonneville
    65 912 slate gray "erwin"
    73 914 ravennagreen "ferdl"
    erwin_loves_polo

  10. #10
    Senior Member moito's Avatar
    Join Date
    May 2013
    Location
    AUSTRIA (tu felix)
    Posts
    6,699
    metric (M4 or M5 don`t know by heart) screws have been used to hold the dash..not sheet metal screws

Similar Threads

  1. Early heat exchangers 1964/1965
    By Milou in forum Technical Info
    Replies: 8
    Last Post: 01-14-2014, 10:53 AM
  2. FS: NOS early 911 oil dash guage unit-1964 1965 1966 1967
    By route66kix in forum For Sale: 911 Parts
    Replies: 2
    Last Post: 05-04-2013, 09:07 AM
  3. FS: Late 1964 - Early 1965 Sales Folder
    By evokes in forum For Sale: 911 Parts
    Replies: 2
    Last Post: 02-19-2012, 05:50 PM
  4. FS Rarest of rare: 901, 1964, early 1965 911 SWB Toolkit
    By Allen Henderson in forum For Sale: 911 Parts
    Replies: 7
    Last Post: 10-09-2011, 11:05 AM
  5. Early 1964 tach and 1965 speedo
    By ixxifan in forum General Info
    Replies: 0
    Last Post: 06-15-2010, 12:24 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Message Board Disclaimer and Terms of Use
This is a public forum. Messages posted here can be viewed by the public. The Early 911S Registry is not responsible for messages posted in its online forums, and any message will express the views of the author and not the Early 911S Registry. Use of online forums shall constitute the agreement of the user not to post anything of religious or political content, false and defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, or otherwise to violate the law and the further agreement of the user to be solely responsible for and hold the Early 911S Registry harmless in the event of any claim based on their message. Any viewer who finds a message objectionable should contact us immediately by email. The Early 911S Registry has the ability to remove objectionable messages and we will make every effort to do so, within a reasonable time frame, if we determine that removal is necessary.