Results 1 to 4 of 4

Thread: FS: Weber 40IDF Carburetor Conversion Kit

  1. 12-01-2014, 04:16 AM #1
    dinogoetz
    dinogoetz is offline
    Senior Member
    Join Date
    Aug 2009
    Posts
    128

    FS: Weber 40IDF Carburetor Conversion Kit

    Genuine Weber kit made in Europe. Kit contain necessary parts for installation, carburetor, manifold, adapter, linkage and air cleaner. They were installed on a 356 B engine for approx. 1000mls. So they are near new! Price incl. shipping

    Price 1200$US
    Attached Images Attached Images
    Reply With Quote Reply With Quote
  2. 12-01-2014, 07:12 AM #2
    Jim Breazeale
    Jim Breazeale is offline
    Senior Member
    Join Date
    Aug 2009
    Location
    SF Bay Area
    Posts
    5,575
    That kit is available from Pierce Manifolds in California for $717.45 US including all the necessary gaskets. Adding almost $500.00 to the price for a used set (sans gaskets) may be a bit much, don't you think?

    Regards

    Jim
    Last edited by Jim Breazeale; 12-01-2014 at 08:30 AM.
    Reply With Quote Reply With Quote
  3. 12-01-2014, 11:57 PM #3
    dinogoetz
    dinogoetz is offline
    Senior Member
    Join Date
    Aug 2009
    Posts
    128
    Jim,

    befor writing any post here you should check your statements. You get the Webers alone without anything else for 720. All other parts are not included there.

    Dino
    Reply With Quote Reply With Quote
  4. 12-02-2014, 08:48 AM #4
    Jim Breazeale
    Jim Breazeale is offline
    Senior Member
    Join Date
    Aug 2009
    Location
    SF Bay Area
    Posts
    5,575
    Dearest Dino

    I'm going to give you the benefit of the doubt and assume that English is not your primary language, so click on the link posted here and you will plainly see what Pierce Manifold includes in their kit. Yes, the carbs are included in their price of $717.45.
    I got a kick out of your use of the term "made in Europe".
    Why not just say they were made in Spain?
    You wouldn't be trying to mislead someone, now would you?

    http://www.piercemanifolds.com/product_p/k290%20xe.htm

    Now I need to point out to you that I have been around the block a few times and I am very familiar with these kits.
    I do not like them, but that is not the issue here.

    Warmest Regards

    Jim
    www.easypor.com

    Arguing with a Parts Man is like wrestling with a pig in the mud. Sooner or later, you realize the pig likes it.
    Last edited by Jim Breazeale; 12-03-2014 at 06:24 AM.
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules


Message Board Disclaimer and Terms of Use
This is a public forum. Messages posted here can be viewed by the public. The Early 911S Registry is not responsible for messages posted in its online forums, and any message will express the views of the author and not the Early 911S Registry. Use of online forums shall constitute the agreement of the user not to post anything of religious or political content, false and defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, or otherwise to violate the law and the further agreement of the user to be solely responsible for and hold the Early 911S Registry harmless in the event of any claim based on their message. Any viewer who finds a message objectionable should contact us immediately by email. The Early 911S Registry has the ability to remove objectionable messages and we will make every effort to do so, within a reasonable time frame, if we determine that removal is necessary.