Page 1 of 2 12 LastLast
Results 1 to 10 of 13

Thread: FS: Koni Struts

  1. 04-08-2013, 10:29 AM #1
    drakon
    drakon is offline
    Junior Member
    Join Date
    Apr 2013
    Posts
    9

    FS: Koni Struts

    New to this board. Actually was referred by one of the 914 World members.

    I recently bought a build in progress of a nice 914. The PO wanted to flair the car and put a 911 front end in, but I'm not going to take that path.

    I have for sale a set of Koni Struts, part number 911.341.079.16

    Also two Koni inserts and threaded caps that seem to be in very fine condition. I turned them all the way closed and can't pull up the shaft and when set at 3 turns, they seem to give me plenty of resistance when I press down quickly on them.

    The struts are naked - meaning they do not have any wheel components on them.

    $850.00.

    Thanks,

    Len

    rear_strut.jpg

    strut_spindle.jpg

    strut_tube.jpg
    Last edited by Chuck Miller; 04-08-2013 at 12:17 PM.
    Reply With Quote Reply With Quote
  2. 04-08-2013, 10:45 AM #2
    neunelfs
    neunelfs is offline
    Senior Member neunelfs's Avatar
    Join Date
    Jun 2011
    Posts
    401
    PM sent. Thanks.
    Reply With Quote Reply With Quote
  3. 04-08-2013, 10:53 AM #3
    Chuck Miller
    Chuck Miller is offline
    Moderator Chuck Miller's Avatar
    Join Date
    Oct 2002
    Location
    Reseda, CA.
    Posts
    12,458
    Len,

    This is a 'stated price' forum... if it's here and not a link to ebay then you must state a price....ASAP
    http://www.early911sregistry.org/for...efore-you-post
    Chuck Miller
    Creative Advisor/Message Board Moderator - Early 911S Registry #109
    R Gruppe #88
    TYP901 #62
    '73S cpe #1099 - Matched # 2.7/9.5 RS spec rebuild
    '67 Malibu 327 spt cpe - Period 350 Rebuild

    ’98 Chevy S-10 – Utility
    ’15 GTI – Commuter
    Reply With Quote Reply With Quote
  4. 04-08-2013, 12:05 PM #4
    drakon
    drakon is offline
    Junior Member
    Join Date
    Apr 2013
    Posts
    9
    Quote Originally Posted by Chuck Miller View Post
    Len,

    This is a 'stated price' forum... if it's here and not a link to ebay then you must state a price....ASAP
    http://www.early911sregistry.org/for...efore-you-post
    Sorry Admin, didn't realize that.

    I'm not a 911 person, but I was told they should bring around $850.00 for the set (struts and inserts).

    So that's what I'd be looking for.
    Last edited by Chuck Miller; 04-08-2013 at 12:18 PM.
    Reply With Quote Reply With Quote
  5. 04-08-2013, 12:50 PM #5
    neunelfs
    neunelfs is offline
    Senior Member neunelfs's Avatar
    Join Date
    Jun 2011
    Posts
    401
    Hi Len.

    I am interested and sent you a private message. Could you post full-length photos of the struts? And please confirm the bolt spacing. Thanks.

    Alex
    Reply With Quote Reply With Quote
  6. 04-08-2013, 01:15 PM #6
    drakon
    drakon is offline
    Junior Member
    Join Date
    Apr 2013
    Posts
    9
    Quote Originally Posted by neunelfs View Post
    Hi Len.

    I am interested and sent you a private message. Could you post full-length photos of the struts? And please confirm the bolt spacing. Thanks.

    Alex

    911 SC A-calipers fit these. I have a pair of them that came with, along with a rebuild kit (for the calipers). Center to center, the holes for calipers are about 3.25", 3" inside to inside edges.

    DSC_0026.JPG

    DSC_0025.JPG

    DSC_0017.JPG

    DSC_0016.JPG
    Reply With Quote Reply With Quote
  7. 04-08-2013, 05:37 PM #7
    drakon
    drakon is offline
    Junior Member
    Join Date
    Apr 2013
    Posts
    9
    911SC a-calipers fit - have a set of those also w/rebuild kit that could go with if needed

    Holes measure about 3.25 inches center to center - 3 inches inside edge to inside edge

    DSC_0026.JPG

    DSC_0025.JPG
    Reply With Quote Reply With Quote
  8. 04-09-2013, 10:34 AM #8
    drakon
    drakon is offline
    Junior Member
    Join Date
    Apr 2013
    Posts
    9
    If you are interesed in these, I've listed them on ebay.
    Reply With Quote Reply With Quote
  9. 04-09-2013, 10:37 AM #9
    Mr9146
    Mr9146 is offline
    Chillin' Mr9146's Avatar
    Join Date
    Nov 2002
    Posts
    6,607
    Pin type or pinch type ball joint?
    -Marco
    SReg. #778 OGrp: #8 RGrp: #---
    TLG Auto: Website
    Searching for engine #907495 and gearbox 902/1 #229687
    Reply With Quote Reply With Quote
  10. 04-09-2013, 10:44 AM #10
    drakon
    drakon is offline
    Junior Member
    Join Date
    Apr 2013
    Posts
    9
    Quote Originally Posted by Mr9146 View Post
    Pin type or pinch type ball joint?
    Pin type....
    Reply With Quote Reply With Quote
« Previous Thread | Next Thread »

Similar Threads

  1. FS: Koni 3 inch front struts (restored by Koni & no road time)
    By Kaleid in forum For Sale: 911 Parts
    Replies: 3
    Last Post: 03-26-2014, 03:41 AM
  2. FS: KONI 3.5" refinised Spindles / struts with new classic koni inserts and bushings
    By budge96 in forum For Sale: 911 Parts
    Replies: 3
    Last Post: 09-15-2013, 11:13 AM
  3. FS: Koni Struts
    By Shaun 69 E in forum For Sale: 911 Parts
    Replies: 3
    Last Post: 07-14-2013, 02:44 PM
  4. FS: '73 S Koni Struts
    By 913 in forum For Sale: 911 Parts
    Replies: 5
    Last Post: 04-23-2013, 05:06 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •  

Forum Rules


Message Board Disclaimer and Terms of Use
This is a public forum. Messages posted here can be viewed by the public. The Early 911S Registry is not responsible for messages posted in its online forums, and any message will express the views of the author and not the Early 911S Registry. Use of online forums shall constitute the agreement of the user not to post anything of religious or political content, false and defamatory, inaccurate, abusive, vulgar, hateful, harassing, obscene, profane, sexually oriented, threatening, invasive of a person's privacy, or otherwise to violate the law and the further agreement of the user to be solely responsible for and hold the Early 911S Registry harmless in the event of any claim based on their message. Any viewer who finds a message objectionable should contact us immediately by email. The Early 911S Registry has the ability to remove objectionable messages and we will make every effort to do so, within a reasonable time frame, if we determine that removal is necessary.